Fumoto Oil Drain Valve F-106 14mm-1.5


Get 2, Ships Free! Order Online or Call: 1-877-350-5584

Home

Vehicle Chart

Size Chart

Customer Care

FAQ

0 items in cart

F-106: Engine Oil Drain Valve 14mm-1.5

Introducing the best way to change oil, the Engine Oil Drain Valve. Install this valve and you can drain your engine oil without tools and without mess. Just lift the lever of this solid brass ball valve and give it a quarter turn to open it. Return the lever to its original position and it locks closed, double sealed to prevent leakage. The Engine Oil Drain Valve is made of corrosion resistant forged brass and stainless steel. The ball valve design provides a straight flow for efficient drainage and a perfect seal when closed. Frozen drain plug and stripped threads are eliminated forever. Drawing samples for oil analysis is as easy as one-two-three. Sizes to fit all cars, light trucks vans heavy-duty trucks and buses.

Installation:

1. Remove original drain plug and drain oil into acceptable receptacle.
2. Insert Engine Oil Drain Valve with gasket and tighten. Do not over tighten. (Some oil pans are designed with recessed drain hole which may prevent the valve from being installed properly. If the valve can not be tightened all the way without hitting the oil pan wall, do not install the Drain Valve to your vehicle. Adapters are available for some models.)
3. Make sure valve is closed and refill crankcase.

Operation:

1. To open lift control lever and turn counter-clockwise 90 degrees.
2. To close simply turn the lever clockwise 90 degrees until locked in original position.

Safety:
1. Drive carefully at all times, and if you run over any foreign object on the road pull over and check the valve for any damage or leak.
2. N-Series valve (with nipple to accept hose) is not recommended for passenger cars with low clearance.

Q: Is my Engine Oil Drain Valve going to leak?

A: No. The "ball valve" design of your Engine Oil Drain Valve is just like the design of valves used in pressurized gas applications. Every valve is constructed to exacting specifications and each and every valve is tested for air tightness before it leaves the factory. The Engine Oil Drain Valve has been tested and granted "Genuine Part" status by six major motor vehicle manufacturers in Japan. These approvals were not granted easily and gaining them was a testimony to the quality and durability of the Engine Oil Drain Valve.

Q: Will my Engine Oil Drain Valve open up while I am one the Road?

A: No. In its closed position the Engine Oil Drain Valve extends from the oil pan only about one half inch more than a standard oil drain plug. The valve's simple but effective locking system requires two distinct actions to open it and its heavy-duty construction will withstand any engine vibration. Over 7,000,000 Engine Oil Drain Valves have been sold in the past eight years and no problems have been reported.

*For users under extreme conditions:
If you are using the Engine Oil Drain Valve on off-road vehicles such as farm tractors and logging equipment under extreme environment (i.e. corn fields, brush areas), it is recommended that a hose clip as shown below be used for extra safety and security. The hose clip, which can be purchased at our online store or any hardware stores, will firmly keep the lever in the locked position at all times.

Clip images

Drain Valve	Hose Clip
All F-Series	5/8"
FG & T-Series	11/16"

Q: How much does the Engine Oil Drain Valve stick out from the oil pan? Is it safe to use the N-Type valve (with Nipple) for cars and light trucks?

A: The Drain Valve for passenger cars and light trucks is approximately 7/8" thick. This means that the valve sticks out only 1/2" more than the regular plug head from the oil pan. The Nipple on the N-Type Valve extends from the valve for 5/8". We do not recommend using the N-Type valve for vehicles with low clearance, as the valve may stick out too far against the ground.

Q: Does my Engine Oil Drain Valve protrude into the interior of the oil pan and prevent full drainage of my engine oil?

A: No. The threaded oil drain plug hole is always reinforced to accept the threaded bolt of the drain plug. Your Engine Oil Drain Valve will not extend past this threaded portion of the drain hole and will allow the oil to be properly drained. Your Engine Oil Drain Valve will let you drain your engine oil while it is hot without burning your hands and it is much more effective than trying to pump the oil out from above.

Q: How long will my Engine Oil Drain Valve last?

A: Your Engine Oil Drain Valve is constructed of corrosion resistant forged brass and stainless steel. To gain the approval of motor vehicle manufacturers it was subjected to minus 40 degrees Fahrenheit temperatures. It endured 336 hours of salt spray and thousands of openings and closings and still functioned perfectly. You can expect the Engine Oil Drain Valve to outlast your engine.

Limited Warranty
Qwik Valve offers a LIFE TIME WARRANTY on its product, against faulty workmanship and/or material to the original purchaser (with proof of purchase). For any defective product, Fumoto Engineering of America will replace the product at no charge. Fumoto Engineering of America will also indemnify any consequencial damages to the engine/vehicle which are directly caused by the defective product. This warranty does not cover any damages due to misuse, abuse, negligence or accident. This warranty is valid only in the United States and Canada.

30 Days Exchange or Money Back Guarantee
If the size of the item doesn't fit and you need to exchange it, or if you are not satisfied with our product and you want to get a refund, it is very easy to exchange or get a refund. For more info, please visit our customer care page.

Details


SKU	F-106
Weight	0.30 lbs
Dimension	7/8" in length (Only stick out 1/2" more than standard oil plug head.)
Size	14mm-1.5
Price:	$22.95

Options

Quantity

add to cart